Category: Lead

Updated October 16, 2026, by the RB Water Desk. How we research.

The certified lead pitchers at a glance

A pitcher filter only counts as a lead filter if it is certified to NSF/ANSI 53 for lead by an accredited certifier. In that test, water spiked with about 150 ppb of lead runs through the filter for its whole rated life, at two pH levels, and the filtered water must stay at or below 5 ppb. The US EPA points consumers to exactly this certification, together with Class I particulate reduction, in its consumer tool for choosing lead filters.

We checked the current performance data sheet for each filter below on October 16, 2026. A data sheet is the leaflet (also posted online) that lists every certified claim, the test concentration and the result. We have not lab-tested any of these filters ourselves, and we have no commercial relationship with Brita, PUR, ZeroWater or Culligan.

Filter (model)	Lead result, NSF/ANSI 53	Also certified for	Rated life	Certifier on data sheet
Brita Elite (OB06)	99.5% (pH 6.5), 99.6% (pH 8.5)	Microplastics 99.6%, chlorine taste 97.4%, many chemicals	120 gallons or about 6 months	WQA (lead); NSF for the Pacifica pitcher system
PUR PLUS (PPF951K)	99.9% (pH 6.5), 99.2% (pH 8.5)	Total PFAS 99.75%, microplastics 99.8%, chlorine taste 97.5%	40 gallons or 2 months	IAPMO R&T
ZeroWater 5-stage (ZR-001 / ZF-201)	98.9% (pH 6.5), 98.8% (pH 8.5)	PFOA/PFOS 99.8%, chromium, mercury, chlorine taste	15 gallons	IAPMO R&T
Culligan with ZeroWater Technology (ZEROF01)	98.9% (pH 6.5), 98.8% (pH 8.5)	Fluoride 99.7%, total PFAS 99.7%	20 gallons	Tested to NSF/ANSI 42, 53, 401 (Culligan names IAPMO on its product page)
Brita Standard (OB03)	Not certified	Chlorine taste, copper, cadmium, mercury, zinc	40 gallons or about 2 months	—
PUR blue filter (PPF900Z)	Not certified	Chlorine taste, some metals and chemicals	40 gallons or 2 months	IAPMO R&T (other claims)

Every certified filter in that table lands far below the 5 ppb pass line in testing, so the choice between them is not really about lead percentages. It comes down to three practical questions: what else is in your water, how much you drink each day, and how often you are willing to change the filter. The sections below take each filter in turn, then the ones that look similar on the shelf but carry no lead claim.

Brita Elite: the fewest filter changes

Best for: city water where lead is the main worry, and people who forget to change filters.

The Brita Elite (model OB06, sold for years as Longlast+) is the lead-certified pitcher filter with the longest rated life: 120 gallons, which Brita says is about 6 months for an average family. On the data sheet it averaged 99.5 percent lead reduction at pH 6.5 and 99.6 percent at pH 8.5 from a 150 ppb challenge. It is also certified for microplastics (99.6 percent of 0.5 to 1 micron particles under NSF/ANSI 401), chlorine taste and odor, mercury, cadmium, asbestos and a list of pesticides and solvents.

Two details on the data sheet matter. First, Brita caps use at 2 gallons a day “for maximum efficiency”. A family that filters more than that should look at a faucet or under-sink filter instead. Second, the lead certification is tied to the pitchers listed on the sheet; Brita’s lead page says the NSF lead certification applies “when used with” its Pacifica pitcher, and the sheet lists the compatible systems. If you put an Elite filter in an older or third-party pitcher, check that the pitcher model is on the sheet.

On PFAS, the record is mixed. One current Brita Elite data sheet on brita.com lists PFOA and PFOS reduction (98.1 percent) certified by IAPMO R&T, but Brita’s Elite product page makes no PFAS claim, and our full breakdown of what Brita filters remove found no PFAS row on the sheet we read earlier this month. If PFAS matters to you, read the leaflet that comes in your box rather than relying on either.

PUR PLUS: lead, PFAS and microplastics in one pitcher filter

Best for: households that want one pitcher filter covering lead, PFAS and microplastics.

The PUR PLUS pitcher and dispenser filter (model PPF951K) is certified by IAPMO R&T under NSF/ANSI 53 for lead, with 99.9 percent average reduction at pH 6.5 and 99.2 percent at pH 8.5. It also carries a total PFAS claim (99.75 percent, from a mix of seven PFAS compounds) and a microplastics claim (99.8 percent). That combination of lead, total PFAS and microplastics on one pitcher data sheet is what PUR has been advertising since September 2026.

The trade-off is filter life. PUR rates both of its pitcher filters for 40 gallons or 2 months, whichever comes first, at up to 2 gallons a day, so you will change it about three times as often as a Brita Elite. PUR rates the filter for water between 34°F and 82°F; never run hot water through it.

Watch the model number. The same PUR pitchers also take the cheaper blue filter (PPF900Z), which is not certified for lead, PFAS or microplastics. A PUR pitcher on a shelf can hold either. Our page on what PUR filters remove lists every claim for all four PUR cartridges.

ZeroWater: lead plus fluoride or PFAS, at the cost of filter life

Best for: soft or low-mineral city water, and people who also want fluoride (Culligan filter) or PFOA/PFOS reduced.

Both ZeroWater filters on US shelves are certified under NSF/ANSI 53 for lead: 98.9 percent at pH 6.5 and 98.8 percent at pH 8.5. The standard 5-stage filter’s April 2026 data sheet names IAPMO R&T as the certifier, adds PFOA/PFOS (99.8 percent), chromium and mercury, and gives a rated life of 15 gallons. The newer Culligan with ZeroWater Technology filter (ZEROF01) keeps the same lead result and adds certified fluoride (99.7 percent) and total PFAS (99.7 percent) claims, with a rated life of 20 gallons. It only fits the newer Culligan ZeroWater pitchers.

ZeroWater works differently from Brita and PUR. Its large ion exchange stage removes nearly all dissolved minerals, which is why the bundled meter reads 000. The catch is that the same resin is used up by harmless calcium and magnesium, so on hard water the filter can run out well before its rated gallons, and on any water you will change it far more often than a carbon pitcher filter. If you want lead covered for the whole rated life, change it at the rated gallons rather than waiting for the meter to read 006. Our ZeroWater vs Brita comparison goes into the meter, the taste and the filter count.

Popular pitchers that are not certified for lead

Several pitchers that rank in shopping results either have no lead claim or describe lead results without a named certification. That does not prove they remove nothing. It means nobody has certified a lead result you can check.

• Brita Standard (OB03). The basic white Brita filter. Its data sheet covers chlorine taste and some metals (copper, cadmium, mercury, zinc), but not lead. It is often the default filter in a new Brita pitcher, so check what came in the box.
• PUR blue pitcher filter (PPF900Z). Certified for chlorine taste and a few metals, marked “not certified” for lead on PUR’s own data sheet.
• LifeStraw Home pitcher. LifeStraw’s product page says the pitcher “meets NSF 53 standards” for PFOA and PFOS and lists lead among the metals its carbon filter reduces, based on independent lab tests. It does not name a certifier or listing for lead. “Meets the standard” in a lab report is not the same as a certification with ongoing audits.
• Clearly Filtered pitcher. Clearly Filtered’s help center says it is moving its NSF/ANSI 42 and 372 certifications from WQA to NSF and is “pursuing” new NSF/ANSI 53 and 401 certifications with NSF. Until a lead listing appears, treat its lead numbers as the brand’s own lab results.

Brands can and do add certifications, so this list can change. The point is the method: if you cannot find lead on the data sheet with a standard, a result and a certifier, and you cannot find the model in a certifier’s directory, it is not a certified lead filter.

How many filters a year each one needs

Rated life decides how often you shop for cartridges, and the totals differ by a factor of ten. The table counts whichever limit you hit first: gallons, or the time limit where the maker gives one (6 months for Brita Elite, 2 months for PUR). ZeroWater gives a gallon rating only. These are examples, not predictions; ZeroWater on hard water will need more.

Filtered water per day	Brita Elite	PUR PLUS	ZeroWater 5-stage	Culligan ZeroWater
Half a gallon (182 gal/yr)	2	6	13	10
1 gallon (365 gal/yr)	4	10	25	19
2 gallons (730 gal/yr)	7	19	49	37

As a worked example, a couple filtering a gallon a day for drinking, coffee and cooking would buy about 4 Brita Elite filters, 10 PUR PLUS filters or 19 to 25 ZeroWater filters a year. To compare cost, multiply your count by the price per filter you see for the pack size you would buy; we do not quote prices because they change every week. For a household at 2 gallons a day, the pitcher itself becomes the bottleneck, which is the point where a faucet filter makes more sense.

How to confirm the lead claim on the box in two minutes

The EPA’s guide to identifying lead-certified filters says the certification mark and the standards appear on the filter, its packaging or the smallest box it comes in, and that the specific lead claim is often on the performance data sheet, in the certifier’s online directory or on the maker’s website. In practice:

1. Find the model number on the cartridge or box (OB06, PPF951K, ZR-001, ZEROF01 and so on).
2. Look for a certification mark from NSF, IAPMO R&T, WQA, UL Solutions or CSA, next to wording such as “tested and certified against NSF/ANSI 53”.
3. Open the performance data sheet and find the row that says lead, pH 6.5 and pH 8.5, with a 150 ppb challenge and a 5 ppb limit.
4. Check the rated capacity on the same sheet. The lead result only covers that many gallons.
5. Search the model in the certifier’s directory. Our step-by-step guide to checking whether a filter is really NSF certified shows where each directory lives.

Watch for three weaker phrases: “tested to NSF standards”, “meets NSF 53” and “reduces up to 99% of lead” with no standard named. None of them tells you an accredited certifier checked that model. Our guide to NSF 53 vs NSF 58 explains what each standard covers.

Using a pitcher for lead: the rules that matter

A certified pitcher only protects you if it is used the way it was tested. The EPA’s filter maintenance sheet and utility guidance for lead line replacements agree on a short list:

• Use cold water only. Run the tap until the water is cold before filling the pitcher, and never filter hot water. Heat filtered water afterwards if you need it hot.
• Filter all water you drink or cook with, including water for coffee, tea, soup, pasta, pet bowls and infant formula. Showers and dishes do not need it.
• Change the cartridge on time. Reset the indicator light every time you fit a new filter, or track the date and gallons yourself if there is no light.
• Do not overfill or pour early. Let the reservoir drain fully through the filter before you tip the pitcher, so unfiltered water does not slip past.
• Flush first after water has sat. If no one has used the tap for 6 hours or more, run it (not through the filter) before filling the pitcher.
• Do not boil to remove lead. Boiling does not remove lead. Our page on what boiling water does and does not remove covers this.

Some water utilities hand out certified pitchers when they replace a lead service line. Pennsylvania American Water, for example, supplies a pitcher and cartridges free for the first 6 months after a replacement and cites the EPA recommendation to use a filter for 6 months afterwards. Ask your utility before you buy.

When a pitcher is not enough

A lead-certified pitcher is a good stopgap and a reasonable long-term answer for one or two people. It is the wrong tool in a few cases:

• You need more than 2 gallons a day. Both Brita and PUR set that daily limit. A faucet-mount filter certified for lead, or an under-sink carbon or reverse osmosis system certified under NSF/ANSI 53 or 58, handles more water with fewer changes.
• You do not know your lead level. Test first. A pitcher handles a 150 ppb challenge in certification, but you should still know what you are dealing with, and testing again through the filter confirms it works in your home.
• The lead comes from a service line you can replace. The filter treats the symptom. Our guide to lead in tap water covers testing, flushing, utility inventories and replacement programs.
• Your water is from a private well with other problems. Bacteria, nitrate or arsenic need different treatment, chosen after a lab test.

Not sure a pitcher is the right type for your home at all? Answer three questions in the filter finder, or look up what your utility reports with the ZIP code tap-water check. If you also worry about PFAS, our guide to finding out whether your tap water has PFAS shows the free sources.

Sources and how we checked this page

Every claim on this page comes from the filter makers’ performance data sheets and product pages, the US EPA and a water utility’s lead program page, checked on October 16, 2026. We do not test filters in a lab, and we have no commercial relationship with any brand named here. Data sheets change, so check the one in the box you buy.

• Brita: Elite filter (OB06) performance data sheet (PDF)
• Brita: Elite replacement filters product page
• Brita: Lead reduction page
• PUR: Pitcher filters PPF951K and PPF900Z performance data sheet (PDF)
• ZeroWater: 5-stage filter performance data sheet, April 2026 (PDF)
• Culligan: ZeroWater Technology filter performance data (PDF)
• LifeStraw: Home pitcher product page
• Clearly Filtered: Are Clearly Filtered products certified?
• US EPA: Consumer tool for identifying filters certified to reduce lead
• US EPA: How to identify filters certified to reduce lead (PDF, June 2024)
• US EPA: Learn how to maintain your water filter (PDF, August 2025)
• Pennsylvania American Water: Pitcher filter FAQs

Published October 9, 2026. Every claim is checked against the sources listed at the end of this page. How we research.

Where lead in tap water comes from

Lead rarely starts in the river, lake or aquifer your utility draws from. It usually enters water on the way to your glass, as water sits in or flows through plumbing that contains lead. The EPA names three main sources:

• Lead service lines. The pipe that connects the water main in the street to your home. Where one exists, the EPA says it is typically the most significant source of lead in the water.
• Lead solder. Used to join copper pipes in many homes before the federal ban took effect in 1986.
• Brass and chrome-plated brass faucets and fittings. Older fixtures could legally contain far more lead than new ones.

How much lead dissolves depends on the water and the pipes. The EPA and CDC list acidity, low mineral content, temperature, pipe wear and, above all, how long water sits still. That is why the first glass in the morning, or after a vacation, tends to carry the most lead, and why hot water from the tap is riskier than cold.

The age of your home is the best quick clue. The 1986 Safe Drinking Water Act amendments banned plumbing that was not “lead free” from that June on, although “lead free” then still allowed up to 8% lead in pipes and 0.2% in solder. A 2011 law, in force since January 4, 2014, cut the limit to a 0.25% weighted average across the surfaces water touches. So a home built before 1986 has the highest odds of lead parts, a home from 1986 to 2013 can still have leaded brass fixtures, and the newest plumbing contains very little.

Many utilities treat water to make it less corrosive, which keeps lead from leaching. That protection works well most of the time, but a change in treatment or source can undo it. Flint, Michigan is the best-known case. Flint has been below the federal action level since July 2016, and the state reports about 98% of its residential lead lines replaced.

Signs and symptoms: what you can and cannot notice

People search for “signs of lead in water” hoping for a color, a taste or a smell. There isn’t one. The CDC states plainly that lead cannot be seen, tasted or smelled in drinking water. Rusty or discolored water points to iron or sediment, not lead, though old galvanized pipes that rust can also hold lead picked up from upstream lead pipe. Clear water can still contain lead.

Lead in the body is also quiet. The CDC says most children with lead exposure have no obvious immediate symptoms, and that no safe blood lead level in children has been identified. The effects it lists build over time:

Who	Effects reported by the CDC and EPA
Children	Damage to the brain and nervous system, slowed growth and development, learning and behavior problems, lower IQ, hearing and speech problems, anemia
Pregnancy	Lead stored in the mother’s bones can be released, which is linked to reduced fetal growth and premature birth
Adults	Higher blood pressure and heart problems, reduced kidney function

The only way to know whether someone has been exposed is a blood lead test, which most doctors and health departments offer. The CDC uses a blood lead reference value of 3.5 micrograms per deciliter to flag children with more lead than most kids their age. If you have a young child or are pregnant and your water tests positive for lead, ask your doctor about a blood test. Water is one source among several. Old lead paint and dust are another major one.

For questions about symptoms or treatment, talk to a doctor. This page covers the water side: how to find lead, how to measure it, and how to remove it.

Check your service line in 2 minutes

You can often identify your service line yourself. The EPA’s Protect Your Tap guide needs only a coin or key and a magnet. Find where the water pipe enters your home, usually near the water meter in a basement, crawl space or utility closet. Look at the few inches of pipe before the meter or shutoff valve. If it is painted, sand a small spot first.

• Lead: dull gray, soft. Scratching it gently with a coin or key leaves a shiny silver mark. A magnet does not stick.
• Copper: the color of a penny, sometimes with green spots. Scratching shows copper. A magnet does not stick.
• Galvanized steel: dull gray, hard. A scratch stays gray, and a magnet sticks. Galvanized pipe that sat downstream of a lead line can hold lead too.
• Plastic: usually white, black or blue, often with printing on it.

The pipe inside your home is only part of the line. The section under the street or yard can be a different material. Your utility’s records help fill that gap. Under federal rules, every community water system had to build a service line inventory and make it public by October 16, 2024. Homes with a lead, galvanized-requiring-replacement or “unknown” line had to be told so, and those notices continue every year. If you never saw one, call your utility and ask what its inventory lists for your address. Our ZIP code water check tells you which system serves you and its recent lead results from EPA records.

How to test your water for lead

A test of your own tap is the only way to know your lead level. A utility’s average says little about one home, because the lead usually comes from that home’s pipes and fixtures.

Take a first-draw sample

1. Do not use water from that tap for at least 6 hours. Overnight is easiest.
2. Use the cold kitchen or bathroom tap you drink from. Do not run the water first.
3. Fill the lab’s bottle (usually 1 liter) right away, close it and follow the lab’s shipping instructions.
4. Write down the date, the time of the last use, and whether you have removed the aerator. Labs and utilities may ask.

A first-draw sample shows the worst-case water sitting in your fixture and nearby pipe. Some labs or utilities also ask for a second sample after running the water, to see whether the lead comes from the faucet or from farther back in the line. New federal rules for homes with lead lines use a similar idea: utilities collect both the first and the fifth liter and use the higher result.

Certified lab or home test kit?

Option	What it costs	How reliable	Use it for
Free utility test	Free where offered	Lab analysis	Your first step: many public systems test on request
State-certified lab	About $15 to $100 (EPA estimate)	Measures in ppb, catches low levels	The result you act on
Home test strip	Varies	Often misses lead at levels that matter	A rough screen at most; confirm with a lab

The doubts about strips come from evidence. A 2021 Virginia Tech study in Environmental Science & Technology checked 16 consumer kits. Twelve had detection limits of 5 to 20 milligrams per liter, which is hundreds to over a thousand times above the 15 parts per billion action level. Simple yes/no strips picked up dissolved lead better but missed lead particles. The San Francisco utility also rated kit results for lead as mixed and advises confirming any worrying reading with a certified lab.

To find a certified lab, use the EPA’s list of state lab certification programs. The EPA itself does not test home water on request. On a private well, testing is fully your job, and your state health department can point you to labs.

How to read a lead result

Lead results are usually in parts per billion (ppb), the same as micrograms per liter (µg/L). Some labs report milligrams per liter (mg/L). To convert, multiply mg/L by 1,000: 0.015 mg/L is 15 ppb. “ND” or “<” means below what the lab can measure, not proof of zero.

The numbers in the chart mean different things, and mixing them up causes a lot of confusion:

• 0 ppb, the health goal. The EPA’s maximum contaminant level goal for lead is zero, because no safe level is known.
• 5 ppb, the filter test. To earn an NSF/ANSI 53 or 58 lead claim, a filter must cut test water spiked to 150 ppb down to 5 ppb or less. The bar was 10 ppb until a 2019 update.
• 10 ppb, the new action level. Starting November 1, 2027, utilities must act if more than 10% of homes they sample exceed 10 ppb.
• 15 ppb, today’s action level. The current trigger for utility action. It is a treatment trigger, not a safety line for your glass.

So a 6 ppb result does not mean your water is “safe” because it is under 15. It means there is lead in your water, at a level a certified filter is built to handle. Retest after changes such as plumbing work, a new filter, or a utility notice about treatment changes.

What federal lead rules say now

The EPA finalized the Lead and Copper Rule Improvements (LCRI) in October 2024, and it took effect December 30, 2024. Its main changes for households:

• The lead action level drops from 15 to 10 ppb, with compliance starting November 1, 2027.
• Utilities must replace lead and certain galvanized service lines under their control, generally within 10 years. Cities with very many lead lines can get longer deadlines.
• Sampling in homes with lead lines uses the higher of the first- and fifth-liter results, which catches more lead from the line itself.
• Utilities must keep updating service line inventories and notifying affected homes.

The rule is being challenged in court by the American Water Works Association. The EPA said in August 2025 that it would defend the rule, and oral argument was held on September 30, 2026. A decision has not been issued. The EPA now estimates about 4 million lead service lines in the US, down from an earlier estimate of about 9 million, as utilities have identified more of their pipes. Chicago alone has more than 400,000 confirmed or suspected lead lines.

Replacement takes years even where funding exists. A filter is the practical protection in the meantime.

What to do today if you might have lead

1. Use only cold water for drinking, cooking and baby formula. Hot water dissolves more lead.
2. Flush pipes before drinking by running the tap, showering or running a load of laundry or dishes. The EPA does not give one fixed time, because it depends on whether you have a lead line and how long it is. Ask your utility how long to flush.
3. Clean faucet aerators regularly. Lead particles can collect in the screen.
4. Do not boil water to remove lead. It stays behind and can concentrate slightly. See what boiling does and does not remove.
5. Use a filter certified for lead at the tap you drink from, and change cartridges on time.
6. Ask about replacement. If you have a lead line, ask your utility about its replacement program and any help with the private side of the line.

What about showers? The EPA says bathing and showering should be safe even if water contains lead above the action level, because human skin does not absorb lead in water. The concern is water you drink or cook with.

Filters that work for lead

Look for a certification, not marketing words. The certification that matters for lead is NSF/ANSI 53 (or NSF/ANSI 58 for reverse osmosis) with lead listed as a certified reduction claim. The EPA’s consumer tool for lead filters also advises looking for NSF/ANSI 42 Class I particulate reduction, because some lead travels as tiny particles. Our guide to NSF 53 vs 58 explains how the two health standards differ.

Watch for one common mix-up. NSF/ANSI/CAN 372 certifies that a product’s own parts are low in lead (no more than 0.25% weighted average). It says nothing about removing lead from water. A filter that shows only “372” has not been shown to reduce lead. Our certifications explainer covers all the numbers you will see on a box.

Filter type	Can be certified for lead?	Good to know
Pitcher	Yes, some models	Cheapest start. Small volume and slow; only some cartridges carry a lead claim
Faucet-mount	Yes, many models	Filters on demand at the kitchen tap; does not fit every faucet
Refrigerator	Some cartridges	Depends on the exact part number
Under-sink carbon	Yes, many models	More capacity; needs a cold-water connection
Reverse osmosis	Yes (NSF/ANSI 58)	Also reduces fluoride, nitrate, arsenic and more; wastes some water
Whole-house	Rarely the right tool	Lead usually enters at fixtures and the line; filter at the tap you drink from

A few examples we checked on manufacturer pages on October 7, 2026. These are examples, not tested picks:

• Brita Elite pitcher filter: Brita says it is certified to NSF/ANSI 53 for lead, reduces 99% of lead, and should be replaced every 120 gallons, about 6 months for an average family.
• PUR faucet filters: PUR sells a faucet filter it calls its “Lead Reducing Faucet Filter” and rates its faucet filters for 100 gallons or 3 months.
• Refrigerator cartridges: some carry NSF/ANSI 53 lead claims, such as the everydrop Filter 1, which its listings rate at 200 gallons or 6 months. Many cheaper look-alike cartridges carry no lead claim.

Not sure which type fits your kitchen and budget? The filter finder asks a few quick questions, and our water filter buying guide walks through the full decision.

How to verify a lead claim in 3 minutes

1. Find the exact model or cartridge number on the box or product page.
2. Open the certifier’s listing: NSF, IAPMO R&T, WQA, UL Solutions or CSA. The EPA accepts all five.
3. Search the model number and look for “Lead Reduction” under NSF/ANSI 53 or 58.
4. Open the performance data sheet and note the rated capacity in gallons. That is when the lead claim stops being backed.

“Tested to” or “meets the standard” wording is weaker than “certified.” It may mean a single lab test the brand paid for, without ongoing audits. Our step-by-step guide shows how to check if a filter is really NSF certified, with screenshots of what a real listing looks like.

Sources and how we checked this page

Facts on this page come from the EPA, the CDC, the Federal Register, NSF and peer-reviewed research, checked on October 7, 2026. Product details come from manufacturer pages on the same date. We do not test water or filters in a lab.

• EPA: Basic information about lead in drinking water
• CDC: Lead in drinking water
• CDC: About childhood lead poisoning prevention
• CDC: Symptoms and complications of lead exposure
• EPA: Protect Your Tap, a quick check for lead
• EPA: Lead and Copper Rule Improvements
• Federal Register: Lead and Copper Rule Improvements final rule (Oct 30, 2024)
• Louisiana Department of Health: LCRI FAQ, compliance dates (May 2026)
• NRDC: AWWA v. EPA, Lead and Copper Rule Improvements case
• EPA: 7th Drinking Water Infrastructure Needs Survey update, 4 million lead lines (Nov 2025)
• EPA: Service line inventory requirements (Nov 2025)
• EPA: Use of lead-free pipes, fittings, fixtures, solder and flux
• EPA: Consumer tool for identifying filters certified to reduce lead
• EPA: Certified laboratories for drinking water
• Water Online: Stricter lead reduction requirements for NSF/ANSI 53 and 58 (2020)
• WC&P: A closer look at NSF/ANSI/CAN 372 low-lead certification (2024)
• Virginia Tech: Kriss et al., evaluation of consumer lead test kits (2021)
• SFPUC: Home test kits
• SFPUC: How to check your water service line for lead
• Michigan EGLE: Flint enters 10th year of lead compliance (Feb 2026)
• Inside Climate News: Chicago lead service lines (Sep 2025)
• Brita: Lead reduction and Elite filter
• PUR: Faucet filter
• ZeroWater: Certified results
• NSF: Certified drinking water treatment units listing